Key takeaways
- Compare the best cabinet knobs and pulls for a kitchen refresh, with hole spacing, finishes, materials and pack sizes explained before you buy.
Swapping cabinet hardware is one of the few kitchen updates that needs no plumber, no electrician and no demolition. A screwdriver, an hour or two, and a matching set of knobs or pulls can change how the whole room reads. The catch is that hardware is sold by measurements, not by looks alone, and ordering the wrong size is the most common way this simple project goes sideways.
As an Amazon Associate, we earn from qualifying purchases.
The five picks below cover the three shapes you will actually choose between: knobs, which mount through a single hole; bar pulls, which mount through two holes and give a full grip; and cup pulls, the half-moon bin style usually fitted to drawers. Before anything else, measure the hole spacing on your existing pulls, centre to centre. That number decides which pulls replace your old ones without drilling.
This article contains affiliate links, and we may earn a commission when you buy through them at no extra cost to you.
Quick Answer
For most kitchen refresh projects, start with the Ravinte 35-pack matte black bar pulls. They use the common 3 inch hole spacing, the stainless steel build suits busy kitchens, and the large pack covers a typical run of doors and drawers in one order. If your cabinets have 5 inch spacing, the Ravinte Hardware brushed nickel pulls below match instead.
Ravinte 35 Pack Bar Pulls, Matte Black, 3 Inch Hole Center
This is the straightforward modern option: a straight Euro-style bar pull in a flat matte black finish, sold in a 35 pack sized for whole-kitchen jobs rather than one or two drawers. The overall length is 5 inches on a 3 inch centre-to-centre mounting, the most common spacing on recent cabinetry, so it may drop straight into existing holes.
Ravinte lists the material as stainless steel, a sensible pick for a kitchen where hardware gets handled with wet or greasy hands all day. The matte black finish pairs easily with black appliances and dark faucets, and contrasts cleanly against white or light grey painted cabinets.
The high pack count suits a full refresh where every door and drawer gets the same pull. Count your doors and drawers before ordering; wide drawers often work better with two pulls, which eats into the count faster than expected.
Specs:
– Type: Bar pull
– Hole spacing: 3 inches centre to centre
– Overall length: 5 inches
– Finish: Matte black
– Material: Stainless steel
– Pack count: 35 pulls
– Screws included: Not stated in the listing details reviewed
See the Ravinte matte black bar pulls on Amazon
Ravinte Hardware 30 Pack Brushed Nickel Cabinet Pulls, 5 Inch Hole Center
If your existing pulls sit on 5 inch (128 mm) centres, this is the matching pick here. It comes from Ravinte Hardware, the brand’s heavier line; the listing describes the pulls as solid and heavy duty, with a projection of 1.1 inches that leaves comfortable room for fingers behind the bar.
The brushed nickel finish is the traditional workhorse option. It sits comfortably alongside stainless appliances and nickel faucets, and the brushed surface shows fingerprints and water spots less obviously than a polished finish, which matters on sink cabinet and dishwasher pulls.
Note that 5 inch spacing is less universal than 3 inch or 3-3/4 inch, so confirm your measurement twice before ordering; a pull that is even slightly off will not mount into existing holes.
Specs:
– Type: Bar pull
– Hole spacing: 5 inches (128 mm) centre to centre
– Projection: 1.1 inches
– Finish: Brushed nickel
– Material: Not stated in the listing details reviewed; described by the seller as solid construction
– Pack count: 30 pulls
– Screws included: Not stated in the listing details reviewed
See the Ravinte Hardware brushed nickel pulls on Amazon
Ravinte 10 Pack Cup Pulls, Flat Black, 3 Inch Hole Center
Cup pulls are the drawer specialist of the group. The half-moon bin shape is gripped from underneath with fingertips, and the covered top keeps dust and cooking splashes off the grip area. This Ravinte set uses the same 3 inch hole spacing as the top pick above, so the two can be combined in one kitchen: bar pulls on doors, cup pulls on drawers.
The listed overall length is 3-11/16 inches with a width of 1-1/4 inches, and the finish is flat black over a zinc exterior, with the material listed simply as metal. The pack count is 10, enough for a typical bank of kitchen drawers, and the included components name both the pull and a screw, so mounting hardware is in the box.
One placement note: cup pulls are normally centred on the top rail of the drawer front. If your drawers currently have centred knobs, switching usually means filling the old hole and drilling two new ones.
Specs:
– Type: Cup pull (bin cup)
– Hole spacing: 3 inches centre to centre
– Overall length: 3-11/16 inches
– Width: 1-1/4 inches
– Finish: Flat black
– Material: Metal with a zinc exterior finish
– Pack count: 10 pulls
– Screws included: Yes, screw listed in the included components
See the Ravinte flat black cup pulls on Amazon
Franklin Brass Garrett Mushroom Knobs, Champagne Bronze, 10 Pack
Knobs are the simplest swap of all because each one needs a single hole, so a knob can replace almost any existing knob without measuring anything beyond the screw. This Franklin Brass set, model P42354Z-CZ-B from Liberty Hardware, uses a classic round mushroom profile in a champagne bronze finish, a warm muted gold tone that pairs well with wood cabinets and brass fixtures.
The knob diameter is listed at 1-3/16 inches, a standard size that gives a comfortable pinch grip on doors and drawers. The listing gives the material simply as metal, and the included components are the knob and a screw, so each knob arrives with its mounting screw.
A 10 pack suits a vanity, a small kitchen, or a partial refresh where only the doors get knobs. For a full kitchen, most people pair knobs on doors with pulls on drawers, so plan the knob count around doors only. On wide or heavy drawer fronts, a pull gives better leverage than a knob.
Specs:
– Type: Knob, round mushroom profile
– Mounting: Single hole, single screw
– Diameter: 1-3/16 inches
– Finish: Champagne bronze
– Material: Metal, per the listing
– Pack count: 10 knobs
– Screws included: Yes, knob and screw listed in the included components
– Model: P42354Z-CZ-B, made by Liberty Hardware
See the Franklin Brass Garrett knobs on Amazon
Cosmas 5560SN Round Knobs, Satin Nickel, 25 Pack
Cosmas is a long-running cabinet hardware brand, and the 5560SN is its plain round knob in satin nickel, sold here as a 25 pack. The knob measures 1-1/4 inches across with a 1 inch projection, and the listing states the handle material plainly as die-cast zinc metal, which gives it a solid, weighty feel compared with hollow stamped alternatives.
Satin nickel is the safe coordination choice with stainless appliances and nickel or chrome fixtures, on painted or stained wood alike. The included components are listed as knob and screw, and Cosmas polybags its knobs individually with their screws, which protects the finish in transit.
The 25 pack lands between the small 10 packs and the big bar pull sets, covering most average kitchens if you are doing knobs throughout. Think about your widest, heaviest drawers first; switching to pulls on those usually beats knobs everywhere.
Specs:
– Type: Knob, round
– Mounting: Single hole, single screw
– Diameter: 1-1/4 inches
– Projection: 1 inch
– Finish: Satin nickel
– Material: Die-cast zinc, per the listing
– Pack count: 25 knobs
– Screws included: Yes, knob and screw listed in the included components
– Model: 5560SN
See the Cosmas 5560SN satin nickel knobs on Amazon
How to Choose
Start with the tape measure, not the catalogue. Remove one existing pull and measure from the centre of one screw hole to the centre of the other. The common sizes are 3 inch, 3-3/4 inch and 5 inch (128 mm), and your replacement pull must match that number exactly or you will be drilling and filling holes. Knobs avoid the issue entirely because they use one hole.
Next, decide the shape by job. Bar pulls give a full-hand grip and suit wide drawers. Cup pulls are drawer hardware, gripped from below. Knobs are the flexible default for doors and small drawers. Many kitchens mix them: pulls on drawers, knobs on doors, all in one finish.
Then match the finish to the metals already in the room, and count doors and drawers before choosing a pack size. Finally, check screw length: drawers with a separate front panel often need longer screws, and not every pack includes both lengths.
Who Should Skip
Skip this project if your cabinet doors and drawer fronts are damaged, warped or peeling. New hardware draws the eye and will highlight tired cabinetry rather than hide it; refinish or reface first. Also skip ordering if you have not measured your hole spacing yet. Guessing is how a one-afternoon project turns into a weekend of wood filler.
If your kitchen uses panel-ready appliance doors, the standard pack sizes and screw lengths here may not apply, and a kitchen showroom is the better route. And if you want a finish that exactly matches an existing faucet, order one piece first to compare in your own light, because screen photos of bronze and nickel tones vary a lot.
FAQ
How do I measure centre-to-centre spacing?
Remove the pull and measure between the centres of the two screw holes in the door or drawer front, not the length of the pull itself. A 5 inch long pull often mounts on 3 inch centres, as the top pick here shows, so overall length alone will mislead you.
Can I mix knobs and pulls in one kitchen?
Yes, and it is the most common arrangement. Use pulls on drawers, where the grip and leverage help, and knobs on doors. Keep the finish the same across both so the room reads as one set, and keep placement consistent from cabinet to cabinet.
What if my new pulls do not match the old holes?
You have three options: choose a pull in the correct spacing, switch to knobs and fill the second hole, or fill both holes with wood filler, sand, touch up and drill fresh holes. Filling works well on painted cabinets and is harder to hide on stained wood.
Are longer screws ever needed?
Yes. Doors are usually fine with standard screws, but drawer fronts are often two layers thick, the drawer box front plus a decorative panel, and need a longer screw to reach through both. Keep the old screws until the new set is fitted, in case you need to match their length.
Final Verdict
For a typical kitchen refresh, the Ravinte 35-pack matte black bar pulls are the easiest recommendation: standard 3 inch spacing, stainless steel, and enough pieces in one box to finish the room. Kitchens with 5 inch spacing should go to the Ravinte Hardware brushed nickel set, drawer-heavy layouts will like the Ravinte cup pulls, and knob fans have the Franklin Brass Garrett and the Cosmas 5560SN. Whichever you pick, measure first; that step separates a quick swap from a repair job.
FAQ
How do I measure centre-to-centre spacing?
Can I mix knobs and pulls in one kitchen?
What if my new pulls do not match the old holes?
Are longer screws ever needed?
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Set up recurring deliveries of everyday items on eligible products. Terms and savings are set by Amazon.
Explore Subscribe & SaveCollect the home and kitchen items you want in one registry that guests can shop from.
Create a wedding registryFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAs an Amazon Associate we earn from qualifying purchases.